VPYLB2BPCommunication Module

1 Copyright © Murata Manufacturing Co., Ltd. All rights reserved. 03 August 2022 LBUA0VG2BP User Manual for FCC Since this module is not sold to general end users directly, there is no user manual of module. For the details about this module, please refer to the specification sheet of module. This module should be installed in the host device according to the interface specification (installation procedure). FCC ID:VPYLB2BP ●Warning; CFR §15.521(a) notice This module may not be employed for the operation of toys. Operation onboard aircraft, ship or satellite is prohibited. CFR §15.519 a(2) notice The use of antennas mounted on outdoor structures, e.g., antennas mounted on the outside of a building or on a telephone pole, or any fixed outdoors infrastructure is prohibited. Antennas may be mounted only on the hand heldUWB device. 2 Copyright © Murata Manufacturing Co., Ltd. All rights reserved. 03 August 2022 LBUA0VG2BP User Manual for FCC This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device maynot cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This devicecomplies with below part 15 of FCC Rules. Part 15 Subpart F The modular transmitter is only FCC authorized for the specific rule parts (i.e., FCC transmitter rules) listed on the grant, and the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. The final host product still requires Part 15 Subpart B compliance testing with the modular transmitter installed. The OEM integrator is responsible for ensuring that the end-user has no manual instruction to remove or install module, This module has been evaluated stand alone to meet portable use without restriction, however, if a host product also contains other transmitter(s) and antenna(s), necessary test or evaluation needs to be performed in order to meet the requirement. Antenna Change Notice to Host manufacturer If you desire to increase antenna gain and either change antenna type or use same antenna type certified, a Class II permissive change application is required to be filed by us, or you(host manufacturer) can take responsibility through the change in FCC ID(new application) procedure followed by a Class II permissive change application. This module needs to supply a regulated voltage from host device. •VDD_1V8_DIG: 1.71~1.98V •VDD_1V8_RF: 1.71~1.98V Since there is no space which indicates FCC ID on this module, FCC ID is indicated in a manual. If the FCC ID is not visible when the module is installed inside another device, then the module is installed must also display a label referring to the enclosed module. 3 Copyright © Murata Manufacturing Co., Ltd. All rights reserved. 03 August 2022 LBUA0VG2BP User Manual for FCC Maker Supported Antenna P/NType Gain [dBi] Appearance 5ch9ch MurataMTD-ANT-027-1-A_UWB_ANT18mmPatch0.92.7 4 Copyright © Murata Manufacturing Co., Ltd. All rights reserved. 03 August 2022 LBUA0VG2BP User Manual for FCC ●The following statements must be described on the user manual of the host device of this module; FCC CAUTION Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. *If it is difficult to describe this statement on the host product due to the size, please describe in the User's manual. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device maynot cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. or Contains Transmitter Module FCC ID:VPYLB2BPContains FCC ID: VPYLB2BP 5 Copyright © Murata Manufacturing Co., Ltd. All rights reserved. 03 August 2022 LBUA0VG2BP Operational Description FCC ID of this product is as follows. FCC ID: VPYLB2BP Contents 1.PIN Layout 2.Supply Voltage 3.Power Levels 4.Theory of operation 5. Antenna 6 Copyright © Murata Manufacturing Co., Ltd. All rights reserved. 03 August 2022 1.PIN Layout No. Terminal Name No. Terminal Name No. Terminal Name No. Terminal Name 1GND13ANT025HOST_437COEX_2 2SE_214GND26HOST_138COEX_1 3SE_115GND27HOST_239UART2_TX 4 GPIO05_SENS ORINT 16ANT128HOST_340UART2_RX 5GND17GND29GND41GND 6XTAL2_32K18GND30VDD_1V8_RF42GND 7XTAL1_32K19GND31VDD_1V8_DIG43GND 8GND20ANT232GND44GND 9SWD_CLK21GND33GPIO03_SYNC45GND 10SWD_IO22GND34CHIPENABLE46GND 11GND23GPIO1135RTC_SYNC 12GND24GPIO1436GPIO08 Top View 7 Copyright © Murata Manufacturing Co., Ltd. All rights reserved. 03 August 2022 2.Supply Voltage DUT PIN NameMin.Typ.Max.unit VDD_1V8_DIG1.711.801.98V VDD_1V8_RF1.711.801.98V 3. Power Levels ModulationChannelMAXIMUMTUNE UP TOLERANCE Peak PowerAverage Power BPM-BPSK5, 90dBm/50MHz-41.3dBm/MHz BPSK5, 90dBm/50MHz-41.3dBm/MHz 8 Copyright © Murata Manufacturing Co., Ltd. All rights reserved. 03 August 2022 3. Key Features -MainIC:NXP/SR150 -CompliantwithIEEE802.15.4zHRPPHY -SupportsSHFUWBbands,Ch5(6489.6MHz)and9(7987.2MHz) -Supports62.4MHz,124.8MHzand249.6MHzPRFmode -Dataratesof6.81Mbps,7.8Mbps,27.24Mbpsand31.2Mbps 9 Copyright © Murata Manufacturing Co., Ltd. All rights reserved. 03 August 2022 4.Antenna Maker Supported Antenna P/NType Gain [dBi] Appearance 5ch9ch MurataMTD-ANT-027-1-A_UWB_ANT18mmPatch0.92.7 10 Copyright © Murata Manufacturing Co., Ltd. All rights reserved. 03 August 2022 4.Antenna ■50-ohm line(microstripline pattern) Certification tests are conducted in the following patterns. The 50ohm microstrip line needs to be copied when module is installed in the End product. Murata provides set makers with Gerber data or something similar

Murata Manufacturing Co., Ltd. Date: 2022-06-02 TO: Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding: FCC ID: VPYLB2BP To whom it may concern: We, the undersigned, hereby authorize Compliance Certification Services (Kunshan) Inc and Winkey Wang in Compliance Certification Services (Kunshan) Inc to act on our behalf in all manners relating to application for equipment authorization with respect to the FCC ID above, including signing of all documents relating to these matters. Any and all acts carried out by the agent on our behalf shall have the same effect as acts of our own. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Where our agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by SGS North America, Inc., still resides with Murata Manufacturing Co., Ltd. This authorization is valid until further written notice from the applicant. Print Name: KENJI HAYASHIKOSHI Title: SENIOR MANAGER Signature: On behalf of Company: Murata Manufacturing Co., Ltd. Telephone: 81-75-955-6173 E-mail: [email protected]

Murata Manufacturing Co., Ltd. TO: Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding: Confidentiality Request regarding application for FCC ID: VPYLB2BP LONG TERM CONFIDENTIALITY Pursuant to 47 CFR Section 0.459 and 0.457 of the commission’s rules, the applicant hereby request confidential treatment of the documents listed below, associated with the certification application referenced above. Schematic(s) Block Diagrams Operational Descriptions The documents above contain proprietary information not released to the public. Public disclosure of this information may prove harmful to the business of the applicant. SHORT TERM CONFIDENTIALITY Additionally, the applicant requests the following documents be held confidential until the device is marketed or 180 days from the grant date, whichever is less. If the device is marketed within aforementioned days of the Grant Date, the applicant will notify the TCB per FCC KDB 726920 D01 Confidentiality Request Procedures. External Photos Internal Photos Test Setup Photos User manual(s) Sincerely, Print Name: KENJI HAYASHIKOSHI Title: SENIOR MANAGER Signature: On behalf of Company: Murata Manufacturing Co., Ltd. Telephone: 81-75-955-6173 E-mail: [email protected]

Applicant Declaration Applicant Declaration Rev:0.0 SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia 30024 United States Applicant Legal Business Name Murata Manufacturing Co., Ltd. Address 10-1, Higashikotari 1-chome Nagaokakyo-shi Kyoto 617-8555 Japan Grantee Code VPY FCC ID VPYLB2BP Authorized Contact Name KENJI HAYASHIKOSHI Contact Email [email protected] Contact Phone 81-75-955-6173 I, the undersigned, certify that I am an authorized signatory for the Applicant and therefore declare; a)in accordance with 47CFR2.911(d), all of the statements herein and the exhibits attached hereto are true and correct to the best of my knowledge and belief. b)in accepting a Grant of Equipment Authorization issued by a TCB, under the authority of the FCC, as a result of the representations made in this application, the Applicant is responsible for: (1) labeling the equipment with the exact FCC ID as specified in this application, (2) compliance statement labeling pursuant to the applicable rules, (3) compliance of the equipment with the applicable technical rules, c)if the Applicant is not the actual manufacturer of the equipment, appropriate arrangements have been made with the manufacturer to ensure that production units of this equipment will continue to comply with the FCC’s technical requirements. d)in accordance with 47 CFR 2.909 and KDB394321, the Applicant has read, understood and agrees to accept that they are the responsible party and agree to abide by their responsibilities as specified under 47 CFR 2.909 and KDB394321. e)in accordance with ISO17065, FCC KDB641163, FCC KDB610077, KDB394321 and RSP-100, the Applicant has read, understood, accepts and agrees to abide by the post market surveillance requirements. (1) the Applicant understands, accepts and agrees that a sample may be requested for surveillance testing. (2) the Applicant shall make provisions to always have a production sample available upon request by SGS, FCC and/or ISED. (3) the Applicant shall, upon request by SGS, at the Applicant’s expense, provide a production sample of the requested product to SGS, FCC and/or ISED as instructed. The sample shall include all support devices, cables, software, accessories or other hardware or software required for evaluation, review, certification and audit surveillance of products certified by SGS. f)neither the Applicant nor any party to the application is subject to a denial of Federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. §862 because of a conviction for possession or distribution of a controlled substance. See 47CFR 1.2002(b) for the definition of a “party” for these purposes. g)the Applicant has read, understood, accepts and agrees to abide by the SGS North America, Inc.(TCB) terms and conditions. Link to CFRs: https://www.fcc.gov/wireless/bureau-divisions/technologies-systems-and-innovation-division/rules-regulations-title-47 Link to KDBs: https://apps.fcc.gov/oetcf/kdb/index.cfm Link to RSP-100: https://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf01130.html Applicant Signature: Date: 2022-06-02 Print Name: KENJI HAYASHIKOSHI Title: SENIOR MANAGER *NOTE: This declaration cannot be signed by an Agent, it shall be signed by an authorized person listed in the FCC database

Murata Manufacturing Co., Ltd. Cover Letter-Modular Approval FCC ID:VPYLB2BP Date: 2022-6-2 Gentlemen: There’s a Communication Module that would like to have your authorization as a modular approval. The specific product as below, Communication Module with its designed features and specified description, meets special requirements for Limit modular approval on FCC KDB996369 by cross-reference list below. Company Murata Manufacturing Co., Ltd. Model Name Communication Module Model Number LBUA0VG2BP FCC ID VPYLB2BP Requirement of FCC KDB996369 Comply（Y/N） 1. The modular transmitter must have its own RF shielding. Y The EUT provides the RF shielding. See EUT photo. 2. The modular transmitter must have buffered modulation/data inputs (if such inputs are provided) to ensure that the module will comply with Part 15 requirements under conditions of excessive data rates or over-modulation. Y The EUT has its buffered modulation. Please see the Schematic Diagram. 3. The modular transmitter must have its own power supply regulation. N The EUT has its own power supply regulation, but Power supply for PA is directly. please see the Schematic Diagram. 4. The modular transmitter must comply with the antenna and transmission system requirements of Sections 15.203, 15.204(b) and 15.204(c). The antenna must either be permanently attached or employ a “unique” antenna coupler (at all connections between the module and the antenna, including the cable). The “professional installation” provision of Section 15.203 is not applicable to modules but can apply to limited modular approvals under paragraph (b) of this section. Y The EUT meets the FCC antenna requirements; Instructions are described in Operational description 5. The modular transmitter must be tested in a stand ‐alone configuration, i.e., the module must not be inside another device during testing. Y The EUT was tested with a test board, please see test report and setup photo 6. The modular transmitter must be labeled with its own FCC ID number, and, if the FCC ID is not visible when the module is installed inside another device, then the outside of the device into which the N Due to the small size of this module, the FCC ID cannot be printed on the module body. Post the FCC ID in the User manual. Murata Manufacturing Co., Ltd. module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains Transmitter Module FCC ID:VPYLB2BP” or “Contains FCC ID:VPYLB2BP” Any similar wording that expresses the same meaning may be used. The Grantee may either provide such a label, an example of which must be included in the application for equipment authorization, or, must provide adequate instructions along with the module which explain this requirement. In the latter case, a copy of these instructions must be included in the application for equipment authorization. 7. The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements. A copy of these instructions must be included in the application for equipment authorization. Y The EUT is compliant with all applicable FCC rules. Details instructions for maintaining compliance are give in the User Manual. 8. The modular transmitter must comply with any applicable RF exposure requirements. For example, FCC Rules in Sections 2.1091, 2.1093 and specific sections of Part 15, including 15.319(i), 15.407(f), 15.253(f) and 15.255(g), require that Unlicensed PCS, UNII and millimeter wave devices perform routine environmental evaluation for RF Exposure to demonstrate compliance. In ad dition, spread spectrum transmitters operating under Section 15.247 are required to address RF Exposure compliance in accordance with Section 15.247(b)(4). Y The EUT complies with RF exposure requirement. Thank you. Sincerely, Print Name: KENJI HAYASHIKOSHI Title: SENIOR MANAGER Signature: Murata Manufacturing Co., Ltd. On behalf of Company: Murata Manufacturing Co., Ltd. Telephone: 81-75-955-6173 E-mail: [email protected]

Compliance Certification Services (Kunshan) Inc. Shenzhen Branch Page: 1 of 2 External Photos for FYCR2205000175AT FCC ID: VPYLB2BP Compliance Certification Services (Kunshan) Inc. Shenzhen Branch Page: 2 of 2 EUT Constructional Details (EUT Photos) Module

1 Copyright © Murata Manufacturing Co., Ltd. All rights reserved. 23 June 2022 ：Murata Logo mark 2BP：Model Type name MS1119001：Inspection Number ：Pin 1 Marking ：2DCode LBUA0VG2BPLabel Design and Location There is no space todescribetheFCCID Number. Therefore,it is describedonthemanual andpackage. 6.6mm 5.8mm 0.7mm 0.7mm 0.6mm 1.0mm 2.8mm 2 Copyright © Murata Manufacturing Co., Ltd. All rights reserved. 23 June 2022 The character size is 4 points or more. LBUA0VG2BPLabel Design and Location FCC ID:VPYLB2BP IC: 772C-LB2BP HVIN:LBUA0VG2BP This device complies with part 15 of FCC Rules and Industry Canada’s licence-exempt RSSs. Operation is subjectto the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC CAUTION Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Compliance Certification Services (Kunshan) Inc. Shenzhen Branch Page: 1 of 2 Internal Photos for FYCR2205000175AT FCC ID: VPYLB2BP Compliance Certification Services (Kunshan) Inc. Shenzhen Branch Page: 2 of 2 EUT Constructional Details (EUT Photos) RX ANT0 TX & RX Module

Compliance Certification Services (Kunshan) Inc. Shenzhen Branch Page: 1 of 8 Winkey Wang EMC Technical Manager RF EXPOSURE EVALUATION REPORT Application No.: FYCR2205000175AT Applicant: Murata Manufacturing Co., Ltd. Address of Applicant: 10-1, Higashikotari 1-chome Nagaokakyo-shi, Kyoto 617-8555 Japan Manufacturer: Murata Manufacturing Co., Ltd. Address of Manufacturer: 10-1, Higashikotari 1-chome Nagaokakyo-shi, Kyoto 617-8555 Japan Factory: A. Shenzhen Murata Technology Co., Ltd. B. Komatsu Murata Manufacturing Co., Ltd. Address of Factory: A. 15 CUIJING ROAD, SHENZHEN INDUSTRIAL ZONE PINGSHAN NEW DISTRICT SHENZHEN 518118 CHINA B. 93, Hikarimachi, Komatsu-shi, Ishikawa 923-8626 Japan Equipment Under Test (EUT): EUT Name: Communication Module Model No.: LBUA0VG2BP Trade Mark: muRata FCC ID: VPYLB2BP Standard(s) : FCC Rules 47 CFR §2.1093 KDB 447498 D04 interim General RF Exposure Guidance v01 Date of Receipt: 2022-05-17 Date of Test: 2022-05-26 to 2022-07-07 Date of Issue: 2022-07-08 Test Result: Pass* * In the configuration tested, the EUT complied with the standards specified above. Compliance Certification Services (Kunshan) Inc. Shenzhen Branch Report No.: FYCR220500017502 Page: 2 of 8 Revision Record Version Chapter Date Modifier Remark 01 2022-07-08 Original Authorized for issue by: Tree Zhan/Project Engineer Winkey Wang/Reviewer Compliance Certification Services (Kunshan) Inc. Shenzhen Branch Report No.: FYCR220500017502 Page: 3 of 8 2 Contents Page 1 Cover Page ................................................................................................................................................ 1 2 Contents .................................................................................................................................................... 3 3 General Information .................................................................................................................................. 4 3.1 Details of E.U.T. ................................................................................................................................. 4 3.2 Separation Distance ........................................................................................................................... 4 3.3 Evaluating Location ............................................................................................................................ 4 3.4 Facility ................................................................................................................................................ 4 3.5 Deviation from Standards ................................................................................................................... 4 3.6 Abnormalities from Standard Conditions ........................................................................................... 4 4 FCC Radiofrequency radiation exposure limits .................................................................................... 5 4.1 Blanket 1 mW Blanket Exemption ...................................................................................................... 5 4.2 MPE-based Exemption ...................................................................................................................... 5 4.3 SAR-based Exemption ....................................................................................................................... 6 5 Measurement and Calculation ................................................................................................................. 8 5.1 Maximum transmit power ................................................................................................................... 8 5.2 RF Exposure Calculation ................................................................................................................... 8 Compliance Certification Services (Kunshan) Inc. Shenzhen Branch Report No.: FYCR220500017502 Page: 4 of 8 3 General Information 3.1 Details of E.U.T. Power supply: DC1.8V Frequency Range: 6.24GHz~8.24GHz Modulation Type: BPM-BPSK Number of Channels: 2 Sample Type: Portable production Antenna Type: Patch antenna Antenna Gain: CH5: 0.9dBi; CH9: 2.7dBi 3.2 Separation Distance Minimum test separation distance: 5mm Remark: This minimum test separation distance is determined by the smallest distance from the antenna and radiating structures or outer surface of the device, according to the host form factor, exposure conditions and platform requirements, to any part of the body or extremity of a user or bystander. 3.3 Evaluating Location All tests were performed at: Compliance Certification Services（Kunshan）Inc. Shenzhen branch. Fuyong lab. Xinlong TechnoPark,Fengtang Road, Fuyong Subdistrict, Bao’an, Shenzhen, China Tel: +86 755 8866 3988 Fax: +86 755 2671 0594 No tests were sub-contracted. 3.4 Facility The test facility is recognized, certified, or accredited by the following organizations: • A2LA (Certificate No. 6606.01) Compliance Certification Services（Kunshan）Inc. Shenzhen branch is accredited by the American Association for Laboratory Accreditation(A2LA). Certificate No. 6606.01. • FCC –Designation Number: CN1322 Compliance Certification Services（Kunshan）Inc. Shenzhen branch has been recognized as an accredited testing laboratory. Designation Number: CN1322. Test Firm Registration Number: 718073 • Innovation, Science and Economic Development Canada Compliance Certification Services（Kunshan）Inc. Shenzhen branch has been recognized by ISED as an accredited testing laboratory. CAB identifier: CN0129. IC#: 28189. 3.5 Deviation from Standards None 3.6 Abnormalities from Standard Conditions None Compliance Certification Services (Kunshan) Inc. Shenzhen Branch Report No.: FYCR220500017502 Page: 5 of 8 4 FCC Radiofrequency radiation exposure limits Test exemptions apply for devices used in general population/uncontrolled exposure environments, according to the SAR-based, or MPE-based exemption thresholds. 4.…

Text truncated - open the document above for the full version.

Compliance Certification Services (Kunshan) Inc. Shenzhen Branch Report No.: FYCR220500017501 Page: 1 of 111 Winkey Wang EMC Technical Manager TEST REPORT Application No.: FYCR2205000175AT Applicant: Murata Manufacturing Co., Ltd. Address of Applicant: 10-1, Higashikotari 1-chome Nagaokakyo-shi, Kyoto 617-8555 Japan Manufacturer: Murata Manufacturing Co., Ltd. Address of Manufacturer: 10-1, Higashikotari 1-chome Nagaokakyo-shi, Kyoto 617-8555 Japan Factory: A. Shenzhen Murata Technology Co., Ltd. B. Komatsu Murata Manufacturing Co., Ltd. Address of Factory: A. 15 CUIJING ROAD, SHENZHEN INDUSTRIAL ZONE PINGSHAN NEW DISTRICT SHENZHEN 518118 CHINA B. 93, Hikarimachi, Komatsu-shi, Ishikawa 923-8626 Japan Equipment Under Test (EUT): EUT Name: Communication Module Model No.: LBUA0VG2BP Trade Mark: muRata FCC ID: VPYLB2BP Standard(s) : 47 CFR Part 15 Subpart F Date of Receipt: 2022-05-17 Date of Test: 2022-05-26 to 2022-07-07 Date of Issue: 2022-07-08 Test Result: Pass* * In the configuration tested, the EUT complied with the standards specified above. Compliance Certification Services (Kunshan) Inc. Shenzhen Branch Report No.: FYCR220500017501 Page: 2 of 111 Revision Record Version Chapter Date Modifier Remark 01 2022-07-08 Original Authorized for issue by: Tree Zhan/Project Engineer Winkey Wang/Reviewer Compliance Certification Services (Kunshan) Inc. Shenzhen Branch Report No.: FYCR220500017501 Page: 3 of 111 2 Test Summary Test Item Test Requirement Test method Result Antenna Requirement 47 CFR Part 15 Section 15.519(a2), 15.521(b), 15.203 N/A PASS Conducted Emissions at AC Power Line (150kHz- 30MHz) 47 CFR Part 15 Section 15.521(j), 15.207 ANSI C63.10 (2013) Section 6.2 PASS UWB Bandwidth 47 CFR Part 15 Section 15.503 (a) (d), 15.519(b), 15.521(e) ANSI C63.10 (2013) Section10.1 PASS Shutdown Timing Requirements 47 CFR Part 15 Section 15.519 (a)(1) ANSI C63.10 (2013) Section7.8.4 PASS Radiated Spurious Emissions 47 CFR Part 15 Section 15.519 (c)(d), 15.209, 15.521(c)(d)(h) ANSI C63.10 (2013) Section10.2&10.3 PASS Peak Power and Maximum Average Emissions 47 CFR Part 15 Section 15.519 (c) (e), 15.521(g) ANSI C63.10 (2013) Section10.3 PASS Note: E.U.T./EUT means Equipment Under Test. Pass means the test result passed the test standard requirement, please find the detailed decision rule in the report relative section. Remark: 1.for 47 CFR Part 15.521 General Requirement, Section15.521(f) and (i) are not applicable for this product then not evaluated in the report. 2. UWB devices may not be employed for the operation of toys. Operation onboard an aircraft, a ship or a satellite is prohibited. Compliance Certification Services (Kunshan) Inc. Shenzhen Branch Report No.: FYCR220500017501 Page: 4 of 111 3 Contents Page 1 COVER PAGE ............................................................................................................................................ 1 2 TEST SUMMARY ....................................................................................................................................... 3 3 CONTENTS ................................................................................................................................................ 4 4 GENERAL INFORMATION ........................................................................................................................ 6 4.1 DETAILS OF E.U.T. ............................................................................................................................... 6 4.2 DESCRIPTION OF SUPPORT UNITS ......................................................................................................... 6 4.3 MEASUREMENT UNCERTAINTY .............................................................................................................. 6 4.4 TEST LOCATION .................................................................................................................................... 7 4.5 TEST FACILITY ...................................................................................................................................... 7 4.6 DEVIATION FROM STANDARDS ............................................................................................................... 7 4.7 ABNORMALITIES FROM STANDARD CONDITIONS ..................................................................................... 7 5 EQUIPMENT LIST ...................................................................................................................................... 8 6 RADIO SPECTRUM TECHNICAL REQUIREMENT ............................................................................... 11 6.1 ANTENNA REQUIREMENT .................................................................................................................... 11 6.1.1 Test Requirement: ....................................................................................................................... 11 6.1.2 Conclusion ................................................................................................................................... 11 7 EMISSION TEST RESULTS .................................................................................................................... 12 7.1 CONDUCTED EMISSIONS AT AC MAINS POWER PORT (150KHZ-30MHZ) .............................................. 12 7.1.1 E.U.T. Operation .......................................................................................................................... 12 7.1.2 Test Mode Description ................................................................................................................. 12 7.1.3 Test Setup Diagram ..................................................................................................................... 12 7.1.4 Measurement Procedure and Data............................................................................................. 13 8 RADIO SPECTRUM MATTER TEST RESULTS ..............................…

Text truncated - open the document above for the full version.

Compliance Certification Services (Kunshan) Inc. Shenzhen Branch Report No.: FYCR220500017501 Page: 102 of 111 6489.6MHz_HPRF1_SP 1_STS 1_Payload 0 6489.6MHz_HPRF1_SP 1_STS 2_Payload 0 6489.6MHz_HPRF2_SP 0_Payload 2 6489.6MHz_HPRF2_SP 0_Payload 512 6489.6MHz_HPRF2_SP 0_Payload 1023 6489.6MHz_HPRF2_SP 1_STS 1_Payload 2 Compliance Certification Services (Kunshan) Inc. Shenzhen Branch Report No.: FYCR220500017501 Page: 103 of 111 6489.6MHz_HPRF2_SP 1_STS 1_Payload 512 6489.6MHz…

Text truncated - open the document above for the full version.