WEC-1501Bluetooth Smart Thermometer

Bluetooth Smart Thermometer Model: EM 2239 App Downloads: *Hardware Requirements: iPhone 4s (or above) or Bluetooth v4.0 enabled smart device *Software Requirements iOS 7 (or above) or Android 4.3 (or above) Thank you for selecting Smart Thermo.Simply program your choice of meat type,target temperature or cooking time either on the touch-key display unit or your smart device via the corresponding app. When your grill is cooked to perfection,You do not need to wait by the grill to monitor the cooking status. Best of all,the app allows you to even text- integrating photos of dishes on social community. Probe wrap x1 2032 battery x1 Metal probex1 Touch-key display unit x1 INSTRUCTION PACKAGING CONTENTS CR 1. Current temperature; 2. °C/°F(temperature measurement unit) 3. Pairing indicator 4. power on/off. 5. Bluetooth indicator 6. Thermo logo a. Metal Probe Connector Wire b. Metal probe c. Probe wrap d. Silicone sleeve 1 2 3 4 6 5 a b c d OVERVIEW DISPLAY UNIT-FRONT VIEW 1 2 3 1. Battery compartment 2. Magnet 3. Reset button 1. Remove the battery door by twisting it counter-clockwise 2. Replace the battery with a CR2032 coin cell battery. 3. Ensure the battery is in place, matching the polarities (+/-) and replace the battery door. 4. Press RESET after each battery change. V DISPLAY UNIT-REAR VIEW BATTERY INSTALLATION Carefully then plug the meat probe into the bottom socket. Probe Use Meat Probe Acceptable Temperature Range: -13°F to 572°F (-25ºC to 300ºC) The probe should be cleaned by hand with a dishcloth, standard dishwashing soap and warm water.The probe is not dishwasher safe. Take precaution not to get the probe's wiring wet. Be sure to avoid water exposure to the probe's wiring as well as the area where the probe's wiring meets the probe. The probe is not waterproof and damage may result from water exposure. The probe should never be submersed in water. When using a standard Meat Probe, be sure the probe wire will not be exposed to flames or temperatures exceeding 572°F (300°C). The Meat Probe should always be inserted into the center of the item which is being cooked for an accurate temperature. CONNECTING THE PROBE NOTE POWERING ON & OFF 1. To turn on the SmartThermo, follow these steps: Press the power button located in the bottom of the LCD. The LCD will full screen display while waiting for pairing. 2. To turn off the SmartThermo, follow these steps: Press the power button located in the bottom and hold of the LCD for three seconds. Auto Shut-Off: The SmartThermo will automatically turning off if there is no probe installed. If low battery icon “ ” displays on the screen, please replace with new batteries for the corresponding device. To quickly find the application from the Apple Store , please type 'SmartThermo' as keyword in the search engine. Ensure your mobile device is compatible with iOS 7 and Android 4.3 devices and later, Only compatible with Bluetooth v4.0 devices . You can remotely set the Smart Thermo and read the thermometer information through Bluetooth v4.0 with your mobile device. NOTE CONNECT WITH YOUR SMART DEVICE First of all, you need to pair your Smart Thermo with your smart. “ ” will flash on the screen of the Smart Thermo while pairing and be on after successful pairing. iPhone (4S and later) iPad (3rd generation and later) iPad mini (all generations) iPod touch (5thgeneration and later) TM ® ® ® IOS SERIES MODEL PAIRING YOUR Smart Thermo 1 2 3 4 5 6 7 8 HOME DISPLAY UNIT-WORK 1. Profile (Tap to display toggle between Profile, Temperature or Timer display) 2. Meat and doneness display (Tap to change setting) 3. Set temperature 4. Target temperature icon 5. Temperature trend display 6. Current meat temperature (Tap to display temperature history) 7. Cooking time or count down timer 8. To start count up or count down timer 1. Tap to view the measurement unit options. 2. Tap on your desired unit. 3. Tap to go back to the previous screen to save. You can set your Smart Thermo through the application, such as measurement units. The settings are as follows. To select the measurement unit: Settings the choose food To select food: 1. Tap to view the Profile options of food . 2. Tap on your food type. 3. Tap to select cooking degree and temperature can be adjusted up and down 2 degrees 4. Tap to go back to the previous screen to save. You can freely set alarm temperature by remote device To select the temperature: 1. Tap to view the Profile options of temperature 2. Slide down and up to set temperature you need. Temperature measurement range: -25°C to 300ºC (-13°F to 572°F) 3. Tap to go back to the previous screen to save. You can freely set alarm time of your smart Thermo by remote device. To select the timer: 1. Tap to view the Profile options of timer . 2. Slide down and up to set time you need. Timer measurement range: 23H 59M 59S. 3. Tap to go back to the previous screen to save. Settings the definition temperature Timer setting To select the alarm ring : You can choose any alarm ring from 27 rings . 1. Tap to view the Profile options of rings 2. Tap to choose your favorite ring 3. Tap to go back to the previous screen to save. 4. If food is cooked , alarm ring will ring and show notification menu. Temperature will show on Smart Thermo screen and LED backlight will flash 5 times. Alarm seting Tap on temperature in central. You can view history date which is presented in graphs. You can put the food cooking photos in community and share with others. To select the camera: 1. Tap to view the Profile options of camera 2. Tap on camera button . 3. Tap on share button and food cooking photos you took will be shared in your community. SHARING VIEW HISTORY READINGS TYPE DESCRIPTION DISPLAY UNIT LxWxH 77x65x13.5mm Power Temperature unit Temperature measuring range PROBE WRAP 1xCR2032 3V batteries METAL PROBE Length Heat resistance for metal probe Temperature range 122mm LxWxH 51x51x20.5mm Around 300°C(572°F) -25°C to 300ºC (-13°F to 572°F) °C/°F 100-hour Battery life …

Text truncated - open the document above for the full version.

1 Photographs - EUT Constructional Details Test model No.: EM2239 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm . Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm . Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm . Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.”

EM 2239 MODEL NO: FCC ID:WEC-1501 FCC ID:WEC-1501

1 Photographs - EUT Constructional Details Test model No.: EM2239 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm . Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm . Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.”

SGS-CSTC Standards Technical Services Co., Ltd. No. 1 Workshop, M-10, Middle section, Science & Technology Park, Nanshan District, Shenzhen, Guangdong, China 518057 Telephone: +86 (0) 755 2601 2053 Fax: +86 (0) 755 2671 0594 Email: [email protected] Report No.: SZEM150200076103 Page: 1 of 6 Authorized Signature: Jack Zhang EMC Laboratory Manager The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of SGS International Electrical Approvals or testing done by SGS International Electrical Approvals in connection with, distribution or use of the product described in this report must be approved by SGS International Electrical Approvals in writing. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. All test results in this report can be traceable to National or International Standards. “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 1 Cover page SAR Evaluation Report Application No.: SZEM1502000761CR Applicant: FUZHOU EMAX ELECTRONIC CO., LTD Manufacturer/Factory:: FUZHOU EMAX ELECTRONIC CO., LTD Product Name: Bluetooth Smart Thermometer Model No.(EUT): EM2239 Add Model No.: ET-737, BBQ40 FCC ID: WEC-1501 Standards: 47 CFR Part 1.1307 (2014) 47 CFR Part 2.1093 (2014) KDB447498D01 General RF Exposure Guidance v05r02 Date of Receipt: 2015-02-11 Date of Test: 2015-02-12 to 2015-03-19 Date of Issue: 2015-03-20 Test Result : PASS* * In the configuration tested, the EUT complied with the standards specified above. SGS-CSTC Standards Technical Services Co., Ltd. Report No.: SZEM150200076103 Page: 2 of 6 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 2 Version Revision Record Version Chapter Date Modifier Remark 00 2015-03-20 Original Authorized for issue by: Tested By 2015-03-19 (Chris Zhong) /Project Engineer Date Prepared By 2015-03-20 (Vivi Zhou) /Clerk Date Checked By 2015-03-22 (Sen Lv) /Reviewer Date SGS-CSTC Standards Technical Services Co., Ltd. Report No.: SZEM150200076103 Page: 3 of 6 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 3 Contents Page 1 COVER PAGE .............................................................…

Text truncated - open the document above for the full version.

SGS-CSTC Standards Technical Services Ltd. No. 1 Workshop, M-10, Middle section, Science & Technology Park, Nanshan District, Shenzhen, Guangdong, China 518057 Telephone: +86 (0) 755 2601 2053 Fax: +86 (0) 755 2671 0594 Email: [email protected] Report No.: SZEM150200076102 Page: 1 of 50 Authorized Signature: Jack Zhang EMC Laboratory Manager The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of SGS International Electrical Approvals or testing done by SGS International Electrical Approvals in connection with, distribution or use of the product described in this report must be approved by SGS International Electrical Approvals in writing. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. All test results in this report can be traceable to National or International Standards. “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 1 Cover page FCC REPORT Application No: SZEM1502000761CR Applicant: FUZHOU EMAX ELECTRONIC CO., LTD Manufacturer/ Factory: FUZHOU EMAX ELECTRONIC CO., LTD Product Name: Bluetooth Smart Thermometer Model No.(EUT): EM2239 Add Model No.: ET-737, BBQ40 FCC ID: WEC-1501 Standards: 47 CFR Part 15, Subpart C (2014) Date of Receipt: 2015-02-11 Date of Test: 2015-02-12 to 2015-03-19 Date of Issue: 2015-03-20 Test Result: PASS * * In the configuration tested, the EUT complied with the standards specified above. SGS-CSTC Standards Technical Services Ltd. Report No.: SZEM150200076102 Page: 2 of 50 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm . Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 2 Version Revision Record Version Chapter Date Modifier Remark 00 2015-03-20 Original Authorized for issue by: Tested By 2015-03-19 (Chris Zhong) /Project Engineer Date Prepared By 2015-03-20 (Vivi Zhou) /Clerk Date Checked By 2015-03-22 (Sen Lv) /Reviewer Date SGS-CSTC Standards Technical Services Ltd. Report No.: SZEM150200076102 Page: 3 of 50 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm . Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 3 Test Summary Test Item Test Requirement Test method Result Antenna Requirement 47 CFR Part 15, Subpart C Section 15.203/15.247 (c) ANSI C63.10 2009 PASS Conducted Peak Output Pow…

Text truncated - open the document above for the full version.

1 Photographs - EUT Test Setup Test model No.: EM2239 1.1 Radiated Emission 1.2 Radiated Spurious Emission