X3ZBTMOD1Bluetooth Module

Amp’ed RF Technology, Inc. Rev: 1.0 1/6/2010 BT11 Bluetooth Module OEM General User and Installation Guide I. OEM Usage Intructions Installation The BT11 is a surface mount Bluetooth module supplied on a 24 pin, 6-layer PCB. The final assembly recommended reflow profiles are: For RoHS/Pb-free applications, Sn96.5/Ag3.0/Cu0.5 solder is recommended. ƒ Maximum peak temperature of 230° - 240°C (below 250°C). ƒ Maximum rise and fall slope after liquidous of < 2°C/second. ƒ Maximum rise and fall slope after liquidous of < 3°C/second. ƒ Maximum time at liquidous of 40 – 80 seconds. Layout The area around the BT11 module should be free of any ground planes, trace routings, or metal for at least 6mm from the antenna in all directions. Traces should not be routed underneath the module. Crystal Tuning and Power Calibration These steps are performed by the manufacturer, and must NOT be modified from the settings applied during manufacturing. Any changes to these settings may void the user’s authority to operate this equipment. Operating Conditions The permitted operating and storage temperatures, power supply requirements, and I/O tolerances are specified in the BT11 Datasheet. RF Exposure Warning This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This device's external antenna must be installed in accordance with provided instructions and it must be operated with a minimum of 20 cm spacing between antennas and all persons’ bodies (excluding extremities of hands, wrists and feet) during wireless mode of operation. Further, this transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. Amp’ed RF Technology, Inc. Rev: 1.0 1/6/2010 II. Notice of FCC Regulatory Compliance This module has been tested and found to comply with the FCC Part15 Rules. These limits are designed to provide reasonable protection against harmful interference in approved installations. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Modifications or changes to this equipment not expressly approved by Amp’ed RF Technology Inc. may void the user’s authority to operate this equipment. III. Modular Approval FCC ID: X3ZBTMOD1 In accordance with FCC Part 15, the BT11 is listed above as a Modular Transmitter device. In support of the Modular Transmitter Approval, the following is stated: 1. The module does have its own RF shielding. 2. The module does have buffered modulation / data inputs. 3. The module does regulate its own power supply. 4. The module does have a permanently attached antenna. 5. The module can be tested as a stand-alone device. 6. The module is labeled with the proper FCC ID, and labeling instructions are provided to OEM end users for external product labels. 7. The module does have instruction for proper use. 8. The module does meet the FCC RF regulations. IV. FCC Label Instructions The outside of final products that contain a BT11 device must display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains Transmitter Module FCC ID: X3ZBTMOD1” or “Contains FCC ID: X3ZBTMOD1.” Any similar wording that expresses the same meaning may be used. An example of this label is figure 1 below: Amp’ed RF Technology, Inc. Rev: 1.0 1/6/2010 Figure 1: External Device FCC Label Sample This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any in received, including interference that may cause undesired ope terference ration. Contains Transmitter Module FCC ID: X3ZBTMOD1 Amp’ed RF Technology Input 3VDC 60mA Made in China Model: BT11

Amp’ed RF Technology, Inc FCC ID: X3ZBTMOD1 Report Number: R0912015-247 Page 49 of 52 FCC Part15.247 Test Report 17 EXHIBIT C - EUT PHOTOGRAPHS 17.1 EUT – Top View 17.2 EUT – Bottom View Amp’ed RF Technology, Inc FCC ID: X3ZBTMOD1 Report Number: R0912015-247 Page 50 of 52 FCC Part15.247 Test Report 17.3 EUT – On the supported Board View 17.4 Supported Board Back View Amp’ed RF Technology, Inc FCC ID: X3ZBTMOD1 Report Number: R0912015-247 Page 51 of 52 FCC Part15.247 Test Report 17.5 EUT – Supported Board Port View 17.6 AC/DC Power Adapter

Amp’ed RF Technology, Inc FCC ID: X3ZBTMOD1 Report Number: R0912015-247 Page 44 of 52 FCC Part15.247 Test Report 15 EXHIBIT A – FCC LABELING REQUIREMENT 15.1 FCC ID Label Information As Per FCC § 2.925, (a) Each equipment covered in an application for equipment authorization shall bear a nameplate or label listing the following: (1) FCC Identifier consisting of the two elements in the exact order specified in §2.926. The FCC Identifier shall be preceded by the term FCC ID in capital letters on a single line, and shall be of a type size large enough to be legible without the aid of magnification. Example: FCC ID: XXX123 XXX—Grantee Code 123—Equipment Product Code As Per FCC § 15.19 (a) In addition to the requirements in part 2 of this chapter, a device subject to certification, or verification shall be labeled as follows: (3) All other devices shall bear the following statement in a conspicuous location on the device: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. (5) When the device is so small or for such use that it is not practicable to place the statement specified under paragraph (a) of this section on it, the information required by this paragraph shall be placed in a prominent location in the instruction manual or pamphlet supplied to the user or, alternatively, shall be placed on the container in which the device is marketed. However, the FCC identifier or the unique identifier, as appropriate, must be displayed on the device. 15.2 FCC ID Label Amp’ed RF Technology, Inc FCC ID: X3ZBTMOD1 Report Number: R0912015-247 Page 45 of 52 FCC Part15.247 Test Report 15.3 FCC ID Label on the System 15.4 FCC ID Label Location on EUT As per FCC §15.19 (b) (4), the label shall not be a stick-on, paper label. The label on these products shall be permanently affixed to the product and shall be readily visible to the purchaser at the time of purchase, as described in Section 2.925(d) of this chapter. "Permanently affixed" means that the label is etched, engraved, stamped, silk- screened, indelibly printed, or otherwise permanently marked on a permanently attached part of the equipment or on a nameplate of metal, plastic, or other material fastened to the equipment by welding, riveting, or a permanent adhesive. The label must be designed to last the expected lifetime of the equipment in the environment in which the equipment may be operated and must not be readily detachable. Label here

Amp’ed RF Technology, Inc FCC ID: X3ZBTMOD1 Report Number: R0912015-247 Page 52 of 52 FCC Part15.247 Test Report 17.7 EUT - Without Shielding View 17.8 EUT – Back View ***** END OF REPORT ***** Antenna

Amp’ed RF Technology, Inc FCC ID: X3ZBTMOD1 Report Number: R0912015-247 Page 46 of 52 FCC Part15.247 Test Report 16 EXHIBIT B - TEST SETUP PHOTOGRAPHS 16.1 Conducted Emissions – Front View 16.2 Conducted Emissions – Side View Amp’ed RF Technology, Inc FCC ID: X3ZBTMOD1 Report Number: R0912015-247 Page 47 of 52 FCC Part15.247 Test Report 16.3 Radiated Emissions – Front View (below 1 GHz) 16.4 Radiated Emissions – Rear View (below 1 GHz) Amp’ed RF Technology, Inc FCC ID: X3ZBTMOD1 Report Number: R0912015-247 Page 48 of 52 FCC Part15.247 Test Report 16.5 Radiated Emissions – Front View (Above 1 GHz) 16.6 Radiated Emissions – Rear View (Above 1 GHz)