XPYLISAU2003.75G HSPA Wireless Module

LISA-U series 3.75G HSPA / HSPA+ Wireless Modules System Integration Manual Abstract This document describes the features and the system integration of LISA-U1 series HSPA and LISA-U2 series HSPA+ wireless modules. These modules are complete and cost efficient 3.75G solutions offering up to six-band HSDPA/HSUPA and quad-band GSM/EGPRS voice and/or data transmission technology in a compact form factor. www.u-blox.com locate, communicate, accelerate LISA-U series - System Integration Manual 3G.G2-HW-10002-A2 Page 2 of 159 Document Information Title LISA-U series Subtitle 3.75G HSPA / HSPA+ Wireless Modules Document type System Integration Manual Document number 3G.G2-HW-10002-A2 Document status Preliminary Document status information Objective Specification This document contains target values. Revised and supplementary data will be published later. Advance Information This document contains data based on early testing. Revised and supplementary data will be published later. Preliminary This document contains data from product verification. Revised and supplementary data may be published later. Released This document contains the final product specification. This document applies to the following products: Name Type number Firmware version PCN / IN LISA-U100 LISA-U100-00S-00 10.72 3G.G2-SW-11000 LISA-U100-01S-00 11.40 n.a. LISA-U110 LISA-U110-00S-00 10.72 3G.G2-SW-11000 LISA-U110-01S-00 11.40 n.a. LISA-U120 LISA-U120-00S-00 10.72 3G.G2-SW-11000 LISA-U120-01S-00 11.40 n.a. LISA-U130 LISA-U130-00S-00 10.72 3G.G2-SW-11000 LISA-U130-01S-00 11.40 n.a. LISA-U130-01A-00 11.40 n.a. LISA-U200 LISA-U200-00S-00 21.21 n.a. LISA-U200-01S-00 TBD n.a. LISA-U230 LISA-U230-01S-00 TBD n.a. LISA-U230-01A-00 TBD n.a. This document and the use of any information contained therein, is subject to the acceptance of the u-blox terms and conditions. They can be downloaded from www.u-blox.com. u-blox makes no warranties based on the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and product descriptions at any time without notice. u-blox reserves all rights to this document and the information contained herein. Reproduction, use or disclosure to third parties without express permission is strictly prohibited. Copyright © 2012, u-blox AG. u-blox ® is a registered trademark of u-blox Holding AG in the EU and other countries. Trademark Notice Microsoft and Windows are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. All other registered trademarks or trademarks mentioned in this document are property of their respective owners. LISA-U series - System Integration Manual 3G.G2-HW-10002-A2 Preliminary Preface Page 3 of 159 Preface u-blox Technical Documentation As part of our commitment to customer support, u-blox maintains an extensive volume of technical documentation for our products. In addition to our product-specific technical data sheets, the following manuals are available to assist u-blox customers in product design and development. AT Commands Manual: This document provides the description of the supported AT commands by the LISA-U series modules to verify all implemented functionalities. System Integration Manual: This Manual provides hardware design instructions and information on how to set up production and final product tests. Application Note: document provides general design instructions and information that applies to all u-blox Wireless modules. See Section Related documents for a list of Application Notes related to your Wireless Module. How to use this Manual The LISA-U series System Integration Manual provides the necessary information to successfully design in and configure these u-blox wireless modules. This manual has a modular structure. It is not necessary to read it from the beginning to the end. The following symbols are used to highlight important information within the manual: An index finger points out key information pertaining to module integration and performance. A warning symbol indicates actions that could negatively impact or damage the module. Questions If you have any questions about u-blox Wireless Integration, please: Read this manual carefully. Contact our information service on the homepage http://www.u-blox.com Read the questions and answers on our FAQ database on the homepage http://www.u-blox.com Technical Support Worldwide Web Our website (www.u-blox.com) is a rich pool of information. Product information, technical documents and helpful FAQ can be accessed 24h a day. By E-mail Contact the nearest of the Technical Support offices by email. Use our service pool email addresses rather than any personal email address of our staff. This makes sure that your request is processed as soon as possible. You will find the contact details at the end of the document. Helpful Information when Contacting Technical Support When contacting Technical Support please have the following information ready: Module type (e.g. LISA-U100) and firmware version Module configuration Clear description of your question or the problem A short description of the application Your complete contact details LISA-U series - System Integration Manual 3G.G2-HW-10002-A2 Preliminary Contents Page 4 of 159 Contents Preface ................................................................................................................................ 3 Contents .............................................................................................................................. 4 1 System description ....................................................................................................... 7 1.1 Overview .............................................................................................................................................. 7 1.2 Architecture ........................................................................................................…

Text truncated - open the document above for the full version.

Page 1 of 5 The test results relate only to the individual items which have been tested. This report shall not be reproduced in parts without the written approval of the testing laboratory © Copyright: All rights reserved by CETECOM Laboratory Accreditation and Listings D-PL-12047-01-01 Reg. No.: 736496 MRA US-EU 0003 Industry Canada Reg. No.: 3462D-1 3462D-2 3462D-3 Reg. No.: R-2665, R-2666 C-2914, T-1967 G-301 accredited according to DIN EN ISO/IEC 17025 CETECOM GmbH Laboratory Radio Communications & Electromagnetic Compatibility Im Teelbruch 116 • 45219 Essen • Germany Registered in Essen, Germany, Reg. No.: HRB Essen 8984 Tel.: + 49 (0) 20 54 / 95 19-954 • Fax: + 49 (0) 20 54 / 95 19-964 E-mail: [email protected] • Internet: www.cetecom.com Annex 2: Photographs of EUT to TEST REPORT No.: 6-0082-11-1-2a for According to: FCC Regulations Part 22 & Part 24 IC-Regulations RSS-132 Issue 2, RSS-133 Issue 5 & RSS-Gen Issue 3 u-blox AG RF Data-Module LISA-U200 FCC-ID: XPYLISAU200 IC-ID: 8595A-LISAU200 Annex 2 to Test Report 6-0082-11-1-2a, Page 2 of 5 TR6-0082-11-1-2a-A2.docx Table of contents 1. PHOTOS OF EUT’S AND AE ............................................................................................................................ 3 Annex 2 to Test Report 6-0082-11-1-2a, Page 3 of 5 TR6-0082-11-1-2a-A2.docx 1. Photos of EUT’s and AE EUT A top view (RF Data-module plug on the middle of EUT C (Adapter board)) Annex 2 to Test Report 6-0082-11-1-2a, Page 4 of 5 TR6-0082-11-1-2a-A2.docx EUT C rear side Annex 2 to Test Report 6-0082-11-1-2a, Page 5 of 5 TR6-0082-11-1-2a-A2.docx EUT D(GA.107 magnetic mount antenna) AE 1(AC 100 -240V; 800mA; 50/60 Hz)

Page 1 of 5 The test results relate only to the individual items which have been tested. This report shall not be reproduced in parts without the written approval of the testing laboratory © Copyright: All rights reserved by CETECOM Laboratory Accreditation and Listings D-PL-12047-01-01 Reg. No.: 736496 MRA US-EU 0003 Industry Canada Reg. No.: 3462D-1 3462D-2 3462D-3 Reg. No.: R-2665, R-2666 C-2914, T-1967 G-301 accredited according to DIN EN ISO/IEC 17025 CETECOM GmbH Laboratory Radio Communications & Electromagnetic Compatibility Im Teelbruch 116 • 45219 Essen • Germany Registered in Essen, Germany, Reg. No.: HRB Essen 8984 Tel.: + 49 (0) 20 54 / 95 19-954 • Fax: + 49 (0) 20 54 / 95 19-964 E-mail: [email protected] • Internet: www.cetecom.com Annex 2: Photographs of EUT to TEST REPORT No.: 6-0082-11-1-2b for According to: FCC Regulations Part 22 & Part 24 IC-Regulations RSS-132 Issue 2, RSS-133 Issue 5 & RSS-Gen Issue 3 u-blox AG RF Data-Module LISA-U200 FCC-ID: XPYLISAU200 IC-ID: 8595A-LISAU200 Annex 2 Test Report to 6-0082-11-1-2b, Page 2 of 5 TR6-0082-11-1-2b-A2.docx Table of contents 1. PHOTOS OF EUT’S AND AE ............................................................................................................................ 3 Annex 2 Test Report to 6-0082-11-1-2b, Page 3 of 5 TR6-0082-11-1-2b-A2.docx 1. Photos of EUT’s and AE EUT A top view (RF Data-module plug on the middle of EUT C (Adapter board)) Annex 2 Test Report to 6-0082-11-1-2b, Page 4 of 5 TR6-0082-11-1-2b-A2.docx EUT C rear side Annex 2 Test Report to 6-0082-11-1-2b, Page 5 of 5 TR6-0082-11-1-2b-A2.docx EUT D (GA.107 magnetic mount antenna) AE 1 (AC 100 -240V; 800mA; 50/60 Hz)

Page 1 of 5 The test results relate only to the individual items which have been tested. This report shall not be reproduced in parts without the written approval of the testing laboratory © Copyright: All rights reserved by CETECOM Laboratory Accreditation and Listings D-PL-12047-01-01 Reg. No.: 736496 MRA US-EU 0003 Industry Canada Reg. No.: 3462D-1 3462D-2 3462D-3 Reg. No.: R-2665, R-2666 C-2914, T-1967 G-301 accredited according to DIN EN ISO/IEC 17025 CETECOM GmbH Laboratory Radio Communications & Electromagnetic Compatibility Im Teelbruch 116 • 45219 Essen • Germany Registered in Essen, Germany, Reg. No.: HRB Essen 8984 Tel.: + 49 (0) 20 54 / 95 19-954 • Fax: + 49 (0) 20 54 / 95 19-964 E-mail: [email protected] • Internet: www.cetecom.com Annex 2: Photographs of EUT to TEST REPORT No.: 6-0082-11-1-2a for According to: FCC Regulations Part 22 & Part 24 IC-Regulations RSS-132 Issue 2, RSS-133 Issue 5 & RSS-Gen Issue 3 u-blox AG RF Data-Module LISA-U200 FCC-ID: XPYLISAU200 IC-ID: 8595A-LISAU200 Annex 2 to Test Report 6-0082-11-1-2a, Page 2 of 5 TR6-0082-11-1-2a-A2.docx Table of contents 1. PHOTOS OF EUT’S AND AE ............................................................................................................................ 3 Annex 2 to Test Report 6-0082-11-1-2a, Page 3 of 5 TR6-0082-11-1-2a-A2.docx 1. Photos of EUT’s and AE EUT A top view (RF Data-module plug on the middle of EUT C (Adapter board)) Annex 2 to Test Report 6-0082-11-1-2a, Page 4 of 5 TR6-0082-11-1-2a-A2.docx EUT C rear side Annex 2 to Test Report 6-0082-11-1-2a, Page 5 of 5 TR6-0082-11-1-2a-A2.docx EUT D(GA.107 magnetic mount antenna) AE 1(AC 100 -240V; 800mA; 50/60 Hz)

Page 1 of 5 The test results relate only to the individual items which have been tested. This report shall not be reproduced in parts without the written approval of the testing laboratory © Copyright: All rights reserved by CETECOM Laboratory Accreditation and Listings D-PL-12047-01-01 Reg. No.: 736496 MRA US-EU 0003 Industry Canada Reg. No.: 3462D-1 3462D-2 3462D-3 Reg. No.: R-2665, R-2666 C-2914, T-1967 G-301 accredited according to DIN EN ISO/IEC 17025 CETECOM GmbH Laboratory Radio Communications & Electromagnetic Compatibility Im Teelbruch 116 • 45219 Essen • Germany Registered in Essen, Germany, Reg. No.: HRB Essen 8984 Tel.: + 49 (0) 20 54 / 95 19-954 • Fax: + 49 (0) 20 54 / 95 19-964 E-mail: [email protected] • Internet: www.cetecom.com Annex 2: Photographs of EUT to TEST REPORT No.: 6-0082-11-1-2b for According to: FCC Regulations Part 22 & Part 24 IC-Regulations RSS-132 Issue 2, RSS-133 Issue 5 & RSS-Gen Issue 3 u-blox AG RF Data-Module LISA-U200 FCC-ID: XPYLISAU200 IC-ID: 8595A-LISAU200 Annex 2 Test Report to 6-0082-11-1-2b, Page 2 of 5 TR6-0082-11-1-2b-A2.docx Table of contents 1. PHOTOS OF EUT’S AND AE ............................................................................................................................ 3 Annex 2 Test Report to 6-0082-11-1-2b, Page 3 of 5 TR6-0082-11-1-2b-A2.docx 1. Photos of EUT’s and AE EUT A top view (RF Data-module plug on the middle of EUT C (Adapter board)) Annex 2 Test Report to 6-0082-11-1-2b, Page 4 of 5 TR6-0082-11-1-2b-A2.docx EUT C rear side Annex 2 Test Report to 6-0082-11-1-2b, Page 5 of 5 TR6-0082-11-1-2b-A2.docx EUT D (GA.107 magnetic mount antenna) AE 1 (AC 100 -240V; 800mA; 50/60 Hz)

LISA-U200 Labeling u-blox Italia Roberto Pagano, tm Department January, 18 th 2012 Confidential locate, communicate, accelerate Slide 2 © u-blox Italia S.p.A., January 18, 2012 IP02.TQ.PP.000001 LISA-U200 labeling •The label is placed on the shield which is soldered to the PCB •The shield is not removable from the PCB •FCC ID: XPYLISAU200, IC ID: 8595A-LISAU200 •Fields YY/MM represent Year (last two digits) and Calendar Week LISA Top Side Model: LISA-U200 IMEI: XXXXXXXXXXXXXXX ® PP 0682 YY/WW 810100.XXXX.000 FCC ID: XPYLISAU200 IC ID: 8595A-LISAU200 Made in Austria xxS-00 Thank you! locate, communicate, accelerate

LISA-U200 Labeling u-blox Italia Roberto Pagano, tm Department January, 18 th 2012 Confidential locate, communicate, accelerate Slide 2 © u-blox Italia S.p.A., January 18, 2012 IP02.TQ.PP.000001 LISA-U200 labeling •The label is placed on the shield which is soldered to the PCB •The shield is not removable from the PCB •FCC ID: XPYLISAU200, IC ID: 8595A-LISAU200 •Fields YY/MM represent Year (last two digits) and Calendar Week LISA Top Side Model: LISA-U200 IMEI: XXXXXXXXXXXXXXX ® PP 0682 YY/WW 810100.XXXX.000 FCC ID: XPYLISAU200 IC ID: 8595A-LISAU200 Made in Austria xxS-00 Thank you! locate, communicate, accelerate

Prediction of MPE The device is designed as module to be installed in other devices. This device is to be used only for fixed and mobile applications. If the final product after integration is intended for portable use, a new application and FCC is required. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all the persons and must not be co-located or operating in conjunction with any other antenna or transmitter. The table below is excerpted from Table 1B of 47 CFR 1.1310 titled Limits for Maximum Permissible Exposure (MPE) and Health Canada Safety Code 6, Limits for General Population/Uncontrolled Exposure: 2 4R PG S π = MPE_LISA_U200.xlsx1 / 2 Power density (mW/cm 2 ) f (MHz) /1500 1.0 30 30 Based on the above table the limits are: For 850 MHz frequency band device: 0.57 mW/cm2 For 1700 /1900 MHz frequency band device: 1 mW/cm2 Frequency Range (MHz) 300 – 1500 1500 – 100.000 Averaging time (minutes) 2 4R PG S π = FCC § 2.1091 / IC RSS102, section 2.5.2 The limit for 850 MHz mobile operations where no routine evaluation is required is: 1.5W ERP The limit for 1700 / 1900 MHz mobile operations where no routine evaluation is required is: 3W EIRP Max permissive power according to §24.232 and RSS133: 2W EIRP Max permissive power according to §§22.913(a) and RSS132: 7W ERP Using the equation from page 19 of OET Bulletin 65, Edition 97-01: 2 4R PG S π = 850 MHz frequency band Maximum output power considerations: Mi where: S = power density (in appropriate units, e.g. mW/cm2) P = power input to the antenna (in appropriate units, e.g., mW) G = power gain of the antenna in the direction of interest relative to an isotropic radiator R = distance to the center of radiation of the antenna (appropriate units, e.g., cm) 2 4R PG S π = Mode Maximum conducted output power (dBm) Maximum conducted output power (W) Duty cycle Equivalent conducted output power (Maximum conducted output power x duty cycle) (mW) GPRS32,671,84950%925 EDGE27,30,53750%269 WCDMA23,150,207100%207 P925mWMaximum power input to the antenna: 2 4R PG S π = R20cm S0,57 mW/cm 2 G 1 4,91 dBi 1,50W ERP G 4,25 dBi pp Distance: MPE limit for uncontrolled exposure: Antenna gain (dBi) to comply with MPE limits: ERP power limit according to §2.1091: Antenna gain (dBi) to comply with ERP limits: 2 4R PG S π = G 2 4,25 dBi 7,00W ERP G 3 7,93 dBi ERP power limit according to §22.913: Antenna gain (dBi) to comply with ERP limits: (ERP = Maximum conducted output power x Antenna gain / 1,64) Antenna gain (dBi) to comply with ERP limits: (ERP[dB] = Maximum conducted output power [dB]x Antenna gain [dBi]-2,15) 2 4R PG S π = G 850 MHz band Min (G 1 , G 2, G 3 ) 4,25dBi Therefore the maximum antenna gain for mobile operation to comply with MPE and ERP limits shall not exceed:4,25 dBi 2 4R PG S π = MPE_LISA_U200.xlsx1 / 2 1900 MHz frequency band Maximum output power considerations: Mode Maximum conducted output power (dBm) Maximum conducted output power (W) Duty cycle Equivalent conducted output power (Maximum conducted output power x duty cycle) (mW) GPRS30,271,06450%532 EDGE26,470,44450%222 WCDMA23,730,236100%236 MPE_LISA_U200.xlsx2 / 2 WCDMA23,730,236100%236 P532mW R20cm S1,00 mW/cm 2 G 1 9,75 dBi Maximum power input to the antenna: Distance: MPE limit for uncontrolled exposure: Antenna gain (dBi) to comply with MPE limits: 3,00W ERP G 2 9,66 dBi 2,00W EIRP ERP power limit according to §2.1091: Antenna gain (dBi) to comply with ERP limits: (ERP[dB] = Maximum conducted output power [dB]x Antenna gain [dBi]-2,15) ERP power limit according to §24.232 G 3 2,74 dBi G 1900 MHz band Min (G 1 , G 2, G 3 ) 2,74dBi Therefore the maximum antenna gain for mobile operation to comply with MPE and EIRP limits shall not exceed:2,74 dBi (EIRP = Maximum conducted output power x Antenna gain ) Antenna gain (dBi) to comply with EIRP limits: MPE_LISA_U200.xlsx2 / 2

Page 1 of 48 The test results relate only to the individual items which have been tested. This report shall not be reproduced in parts without the written approval of the testing laboratory © Copyright: All rights reserved by CETECOM Laboratory Accreditation and Listings D-PL-12047-01-01 Reg. No.: 736496 MRA US-EU 0003 Industry Canada Reg. No.: 3462D-1 Reg. No.: 3462D-2 Reg. No.: 3462D-3 Voluntary Controls for Electromagnetic Emissions Reg. No.: R-2665, R-2666 C-2914, T-1967, G-301 accredited according to DIN EN ISO/IEC 17025 CETECOM GmbH Laboratory Radio Communications & Electromagnetic Compatibility Im Teelbruch 116 • 45219 Essen • Germany Registered in Essen, Germany, Reg. No.: HRB Essen 8984 Tel.: + 49 (0) 20 54 / 95 19-954 • Fax: + 49 (0) 20 54 / 95 19-964 E-mail: [email protected] • Internet: www.cetecom.com T E S T R E P O R T No.: 6-0082-11-1-2a for RF Data-Module LISA-U200 FCC-ID: XPYLISAU200 IC-ID: 8595A-LISAU200 According to: FCC Regulations Part 22 & Part 24 IC-Regulations RSS-132 Issue 2, RSS-133 Issue 5 & RSS-Gen Issue 3 u-blox AG Test Report 6-0082-11-1-2a, Page 2 of 48 TR6-0082-11-1-2a.docx Table of contents 1. SUMMARY OF TEST RESULTS...................................................................................................................... 3 1.1. TX Mode TESTS OVERVIEW FCC Part 15/22/24 and Canada IC Standards (RSS) .................................... 3 1.2. RX Mode TESTS OVERVIEW FCC Part 15/22/24 and Canada IC Standards (RSS) .................................... 4 2. ADMINISTRATIVE DATA ............................................................................................................................... 5 2.1. Identification of the testing laboratory ............................................................................................................. 5 2.2. Test location .................................................................................................................................................... 5 2.3. Organizational items ........................................................................................................................................ 5 2.4. Applicant‟s details ........................................................................................................................................... 5 2.5. Manufacturer‟s details ..................................................................................................................................... 5 3. EQUIPMENT UNDER TEST (EUT) ................................................................................................................. 6 3.1. Technical description of main EUT ................................................................................................................. 6 3.2. EUT: Type, S/N etc. and short descriptions used in this test report ................................................................ 7 3.3. Auxiliary Equipment (AE): Type, S/N etc. and short descriptions .................................................................. 7 3.4. EUT set-ups ..................................................................................................................................................... 7 3.5. EUT operating modes ...................................................................................................................................... 8 3.6. Parameter Settings on mobile phone and base station CMU200 ..................................................................... 9 4. DESCRIPTION OF TEST SET-UP’S ................................................................................................................ 10 4.1. GSM-Mode Test Set-up for conducted measurements .................................................................................... 10 4.2. Test set-up for radiated measurements ............................................................................................................ 11 5. MEASUREMENTS ............................................................................................................................................. 12 5.1. Conducted emissions on AC-Power lines ........................................................................................................ 12 5.2. Radiated field strength emissions below 30 MHz ........................................................................................... 14 5.3. Occupied and emission bandwidth .................................................................................................................. 17 5.4. RF Peak power output conducted .................................................................................................................... 19 5.5. RF Peak power output radiated ........................................................................................................................ 21 5.6. Radio Frequency Exposure Evaluation ............................................................................................................ 23 5.7. Radiated and Conducted out of Band RF emissions and Block Edge ............................................................. 26 5.8. Frequency stability on temperature and voltage variations .............................................................................. 35 5.9. Measurement uncertainties .............................................................................................................................. 44 6. ACCREDITATION DETAILS OF CETECOM’S LABORATORIES AND TEST SITES ......................... 44 7. INSTRUMENTS AND ANCILLARY ................................................................................................................ 45 7.1. Used equipment “CTC” ................................................................................................................................... 45 Table of annexes Total pages SEPARTE DOCUMENT TR6-0082-11-1-2A_A1.PDF: DIAGRAM OF TESTING 86 …

Text truncated - open the document above for the full version.

Page 1 of 51 The test results relate only to the individual items which have been tested. This report shall not be reproduced in parts without the written approval of the testing laboratory © Copyright: All rights reserved by CETECOM Laboratory Accreditation and Listings Reg. No.: 736496 MRA US-EU 0003 Industry Canada Reg. No.: 3462D-1 Reg. No.: 3462D-2 Reg. No.: 3462D-3 Voluntary Controls for Electromagnetic Emissions Reg. No.: R-2665, R-2666 C-2914, T-1967, G-301 accredited according to DIN EN ISO/IEC 17025 CETECOM GmbH Laboratory Radio Communications & Electromagnetic Compatibility Im Teelbruch 116 • 45219 Essen • Germany Registered in Essen, Germany, Reg. No.: HRB Essen 8984 Tel.: + 49 (0) 20 54 / 95 19-954 • Fax: + 49 (0) 20 54 / 95 19-964 E-mail: [email protected] • Internet: www.cetecom.com PARTIAL TEST REPORT No.: 6-0082-11-1-2b for RF Data-Module LISA-U200 FCC-ID: XPYLISAU200 IC: 8595A-LISAU200 According to: FCC-Regulations Part 22 & Part 24 IC-Regulations RSS-132 Issue 2, RSS-133 Issue 5 & RSS-Gen Issue 3 u-blox AG Test Report 6-0082-11-1-2b , Page 2 of 51 TR6-0082-11-1-2b.docx Table of contents 1. SUMMARY OF TEST RESULTS...................................................................................................................... 3 1.1. TX Mode TESTS OVERVIEW FCC Part 15/22/24 and Canada IC Standards (RSS) .................................... 3 1.2. RX Mode TESTS OVERVIEW FCC Part 15/22/24 and Canada IC Standards (RSS) .................................... 4 2. ADMINISTRATIVE DATA ............................................................................................................................... 5 2.1. Identification of the testing laboratory ............................................................................................................. 5 2.2. Test location .................................................................................................................................................... 5 2.3. Organizational items ........................................................................................................................................ 5 2.4. Applicant‟s details ........................................................................................................................................... 5 2.5. Manufacturer‟s details ..................................................................................................................................... 5 3. EQUIPMENT UNDER TEST (EUT) ................................................................................................................. 6 3.1. Additional declaration and description of main EUT ...................................................................................... 6 3.2. EUT: Type, S/N etc. and short descriptions used in this test report ................................................................ 7 3.3. Auxiliary Equipment (AE): Type, S/N etc. and short descriptions .................................................................. 7 3.4. EUT set-ups ..................................................................................................................................................... 7 3.5. EUT operating modes ...................................................................................................................................... 8 3.6. Parameter Settings on mobile phone and base station CMU200 ..................................................................... 9 4. DESCRIPTION OF TEST SET-UP’S ................................................................................................................ 10 4.1. Test Set-up for conducted measurements ........................................................................................................ 10 4.2. Test set-up for radiated measurements ............................................................................................................ 11 5. MEASUREMENTS ............................................................................................................................................. 12 5.1. Conducted emissions on AC-Power lines ........................................................................................................ 12 5.2. Radiated field strength emissions below 30 MHz ........................................................................................... 15 5.3. RF Peak power output conducted .................................................................................................................... 19 5.4. RF power output (radiated) ERP/EIRP ............................................................................................................ 21 5.5. Radio Frequency Exposure Evaluation ............................................................................................................ 23 5.6. Occupied bandwidth and emission bandwidth................................................................................................. 26 5.7. Spurious emission measurements at antenna terminals (conducted) ............................................................... 28 5.8. Radiated spurious emission measurements outside the licensee‟s frequency block ........................................ 31 5.9. Frequency stability on temperature and voltage variations .............................................................................. 33 5.10. Measurement uncertainties ............................................................................................................................ 38 6. ACCREDITATION DETAILS OF CETECOM’S LABORATORIES AND TEST SITES ......................... 39 7. INSTRUMENTS AND ANCILLARY ................................................................................................................ 40 7.1. Used equipment “CTC” ..................................................................................................................................…

Text truncated - open the document above for the full version.

Page 1 of 54 The test results relate only to the individual items which have been tested. This report shall not be reproduced in p…

Text truncated - open the document above for the full version.