YWZ-HBCLBHummingbird CableLok

5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598 Certification Exhibit FCC ID: YWZ-HBCLB IC: 3356F-HBCLB FCC Rule Part: 15.247 IC Radio Standards Specification: RSS-210 ACS Project Number: 13-0211 Manufacturer: Alpha - High Theft Solutions Model: HBCLOK Manual Causes of 3 Alarm Technology • The Hummingbird CableLok will alarm if the Lanyard is cut. • The Hummingbird CableLok will alarm if in the detection field of the EAS system. Facts about the Hummingbird Hummingbird CableLok: • Unit houses Hummingbird module and locking mechanism • Long life lithium battery. Battery life depends on the number and duration of alarms • The sound emitted is 95+ decibels • To stop the Hummingbird CableLok from alarming, follow instructions for removing the Lanyard. Protecting (Arming) Merchandise with the Hummingbird CableLok: 1. Loop the Lanyard around a non-removable portion of the merchandise. (Figure 2) 2. To engage the lock, insert the Locking Clip of the Lanyard completely into the Opening of the Housing until you hear a faint click. (Figure 2) (Clip is non-directional and can be inserted either way into Housing.) NOTE: Unit will play a confirmation tune and flash red. Unit is now armed and the LED Light will continue to flash approximately once every five seconds. 3. Merchandise is now secure and ready for display. Removing (Disarming) the Hummingbird CableLok from Merchandise: 1. Align the Ears of the Manager’s Key with the Indents on the Hummingbird CableLok. (Figure 3) NOTE: The Manager’s Key Ears can be placed on either side of the Hummingbird CableLok. 2. Gently push in on the Lanyard until you hear a faint click. Now pull the Lanyard out from the Housing. (Figure 3) 3. Remove the Manager’s Key. NOTE: Store Hummingbird CableLok in the open position for ease of application and to prevent unnecessary battery drain. (Figure 4) Product should be stored 3 feet (1 meter) from Deactivation Units. 4. Product is now ready for sale. For FCC information and compliance, please refer to page 2. ? Please Contact Customer Service: North America: 800.633.2155 For supplemental information, check out our instructional videos at www.alphaworld.com/videos.asp Instructions for the Hummingbird CableLok CAUTION: Do not place credit cards, ATM cards or magnetic media of any kind near the Manger’s Key as this could erase the magnetic strip. Ears Manager’s Key FIG 2 FIG 3 FIG 4 Lanyard Locking Clip LED Indents Ears Available in two (2) Lanyard lengths General Statements (For all devices): Warning: Changes or modifications to this device not expressly approved by Alpha could void the user’s authority to operate the equipment. FCC Information and Compliance RF Exposure This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment may operate in direct contact with the body of the user under normal operating conditions. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. For Class A Devices: “NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.“ Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. Conformément à la réglementation d’Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d’un type et d’un gain maximal (ou inférieur) approuvé pour l’émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l’intention des autres utilisateurs, il faut choisir le type d’antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l’intensité nécessaire à l’établissement d’une communication satisfaisante. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. For supplemental information, check out our instructional videos at www.alphaworld.com/videos.asp Instructions for the Hummingbird CableLok

5015 B. U. Bowman Dr. Buford, GA 30518 August 19, 2013 ACS TCB 5015 B.U. Bowman Drive Buford, GA 30518 Re: FCC ID: YWZ-HBCLB To Whom It May Concern: The following application is submitted on behalf of our client, Alpha - High Theft Solutions, A Division of Checkpoint Systems, Inc., for evaluation of their model HBCLOK for certification under FCC Part 15.247. The HBCLOK provides article surveillance for retail environments. It attaches to the product by looping the cable through a fixed opening on the product and securing each end of the cable with a spring at each end of the cable. The HBCLOK was tested in full to the requirements of the aforementioned rules and was found to be in compliance. Sincerely, Sam Wismer Vice President, Technology Advanced Compliance Solutions, Inc.

Certification Exhibit FCC ID: YWZ-HBCLB IC: 3356F-HBCLB FCC Rule Part: 15.247 IC Radio Standards Specification: RSS-210 ACS Project Number: 13-0211 Manufacturer: Alpha - High Theft Solutions Model: HBCLOK External Photos 5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598 Model: HBCLOK FCC ID: YWZ-HBCLB IC: 3356F-HBCLB Figure 1: External Photo Figure 2: External Photo ACS Project: 13-0211 Advanced Compliance Solutions Page 2 Model: HBCLOK FCC ID: YWZ-HBCLB IC: 3356F-HBCLB Figure 3: External Photo Figure 4: External Photo ACS Project: 13-0211 Advanced Compliance Solutions Page 3 Model: HBCLOK FCC ID: YWZ-HBCLB IC: 3356F-HBCLB Figure 5: External Photo Figure 6: External Photo ACS Project: 13-0211 Advanced Compliance Solutions Page 4 Model: HBCLOK FCC ID: YWZ-HBCLB IC: 3356F-HBCLB Figure 7: External Photo ACS Project: 13-0211 Advanced Compliance Solutions Page 5

5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598 Certification Exhibit FCC ID: YWZ-HBCLB IC: 3356F-HBCLB FCC Rule Part: 15.247 IC Radio Standards Specification: RSS-210 ACS Project Number: 13-0211 Manufacturer: Alpha - High Theft Solutions Model: HBCLOK Label Information Model: HBCLOKFCC ID: YWZ-HBCLBIC: 3356F-HBCLB ACS Project: 13-0211Advanced Compliance SolutionsPage 2 Figure 1: Sample Label and Placement

5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598 Certification Exhibit FCC ID: YWZ-HBCLB IC: 3356F-HBCLB FCC Rule Part: 15.247 IC Radio Standards Specification: RSS-210 ACS Project Number: 13-0211 Manufacturer: Alpha - High Theft Solutions Model: HBCLOK Internal Photos Model: HBCLOKFCC ID: YWZ-HBCLBIC: 3356F-HBCLB ACS Project: 13-0211Advanced Compliance SolutionsPage 2 Figure 1: Internal Photo Figure 2: Internal Photo

Certification Exhibit FCC ID: YWZ-HBCLB IC: 3356F-HBCLB FCC Rule Part: 15.247 IC Radio Standards Specification: RSS-210 ACS Project Number: 13-0211 Manufacturer: Alpha - High Theft Solutions Model: HBCLOK RF Exposure 5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598 Model: HBCLOK FCC ID: YWZ-HBCLB IC: 3356F-HBCLB General Information: Applicant: Alpha – High Theft Solutions, A Division of Checkpoint Systems, Inc. Product Description: The HBCLOK provides article surveillance for retail environments. It attaches to the product by looping the cable through a fixed opening on the product and securing each end of the cable with a spring at each end of the cable. Exposure Conditions: Portable/Mobile. There is potential for the article under surveillance to be in direct contact with the body (e.g. apparel). Environment: General Population/Uncontrolled Exposure Evaluation Result: Compliant Technical Information: Band of Operation: 2405 – 2480 MHz Number of Channels: 16 Modulation Format: O-QPSK Antenna Type/Gain: Printed circuit board wiggle antenna; 2.15dBi (0dBd) Operating Voltage: 3V CR2477 Lithium Battery Maximum Transmitter Conducted Power: 3.87 dBm, 2.44 mW Maximum System EIRP:6.02 dBm, 3.99 mW Reference Documents: 447498 D01 General RF Exposure Guidance v05r01 SAR Test Exclusion Justification (Portable Exposure Conditions): Per KDB 447498 D01 General RF Exposure Guidance v05r01 section 4.3.1 1), the 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤ 50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] · [√f(GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR Note: The minimum test separation distance used is 5 mm per KDB 447498 D01 General RF Exposure Guidance v05r01 according to 1) of section 4.3.1. = [2.44 / 5]*[ √2.480] = 0.488 * 1.575 = 0.769 Conclusion: Based on the results above, the unit meets both body and extremities SAR test exclusion requirements. ACS Project: 13-0211 Advanced Compliance Solutions Page 2 Model: HBCLOK FCC ID: YWZ-HBCLB IC: 3356F-HBCLB MPE Calculation (Mobile Exposure Conditions): The Power Density (mW/cm 2 ) is calculated as follows: S = 2 4R PG π Where: S = power density (in appropriate units, e.g. mW/cm2) P = power input to the antenna (in appropriate units, e.g., mW) G = power gain of the antenna in the direction of interest relative to an isotropic radiator R = distance to the center of radiation of the antenna (appropriate units, e.g., cm) MPE Calculator for Mobile Equipment Limits for General Population/Uncontrolled Exposure* 24803.871.002.442.151.641 200.0008 Power De n si ty (mW/cm^2) Distance (cm) Transmit Frequency (MHz) Radio Power (dBm) Power Density Limit (mW/Cm2) Radio Power (mW) Antenna Gain (dBi) Antenna Gain (mW e q.) Conclusion: Based on the results above, this device complies with the MPE requirements by providing adequate separation between the device, any radiating structure and the general population. ACS Project: 13-0211 Advanced Compliance Solutions Page 3

5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598 Certification Test Report FCC ID: YWZ-HBCLB IC: 3356F-HBCLB FCC Rule Part: 15.247 IC Radio Standards Specification: RSS-210 ACS Report Number: 13-0211.W06.1A Manufacturer: Alpha - High Theft Solutions Model: HBCLOK Test Begin Date: May 13, 2013 Test End Date: May 15, 2013 Report Issue Date: August 19, 2013 FOR THE SCOPE OF ACCREDITATION UNDER LAB Code 200612-0 This report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal Government. Reviewed by: Kirby Munroe Director, Wireless Certifications ACS, Inc. This test report shall not be reproduced except in full. This report may be reproduced in part with prior written consent of ACS, Inc. The results contained in this report are representative of the sample(s) submitted for evaluation. This report contains 20 pages 5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598 TABLE OF CONTENTS 1GENERAL ............................................................................................................................................ 3 1.1PURPOSE.......................................................................................................................................... 3 1.2PRODUCTDESCRIPTION................................................................................................................... 3 1.3TESTMETHODOLOGY ANDCONSIDERATIONS................................................................................. 3 2TEST FACILITIES.............................................................................................................................. 4 2.1LOCATION....................................................................................................................................... 4 2.2LABORATORYACCREDITATIONS/RECOGNITIONS/CERTIFICATIONS................................................ 4 2.3RADIATEDEMISSIONSTESTSITEDESCRIPTION.............................................................................. 5 2.3.1Semi-Anechoic Chamber Test Site .......................................................................................... 5 2.3.2Open Area Tests Site (OATS) ................................................................................................. 6 2.4CONDUCTEDEMISSIONSTESTSITEDESCRIPTION........................................................................... 7 3APPLICABLE STANDARD REFERENCES.................................................................................... 7 4LIST OF TEST EQUIPMENT............................................................................................................ 8 5SUPPORT EQUIPMENT .................................................................................................................... 9 6EQUIPMENT UNDER TEST SETUP BLOCK DIAGRAM ........................................................... 9 7SUMMARY OF TESTS ......................................................................................................................10 7.1ANTENNAREQUIREMENT–FCC:SECTION15.203 ........................................................................10 7.2POWERLINECONDUCTEDEMISSIONS–FCC:SECTION15.207,IC:RSS-GEN7.2.4......................10 7.2.1Measurement Procedure........................................................................................................10 7.36DB/99%BANDWIDTH–FCC:SECTION15.247(A)(2),IC:RSS-210A8.2(A)..............................10 7.3.1Measurement Procedure........................................................................................................10 7.3.2Measurement Results .............................................................................................................10 7.4FUNDAMENTALEMISSIONOUTPUTPOWER–FCC:SECTION15.247(B)(3),IC:RSS-210A8.4(4).12 7.4.1Measurement Procedure........................................................................................................12 7.4.2Measurement Results .............................................................................................................12 7.5EMISSIONLEVELS–FCC:SECTION15.247(D),15.205IC:RSS-2102.2,A8.5 ..............................13 7.5.1Emissions into Non-restricted Frequency Bands...................................................................13 7.5.1.1Measurement Procedure ..........................................................................................................................13 7.5.1.2Measurement Results ..............................................................................................................................13 7.5.2Emissions into Restricted Frequency Bands..........................................................................17 7.5.2.1Measurement Procedure ..........................................................................................................................17 7.5.2.2Duty Cycle Correction.............................................................................................................................17 7.5.2.3Measurement Results ..............................................................................................................................17 7.5.2.4Sample Calculation:.................................................................................................................................18 7.6MAXIMUMPOWERSPECTRALDENSITY IN THEFUNDAMENTALEMISSION–FCC:SECTION 15.247(E)IC:RSS-210A8.2(B) .................................................................................................................19 7.6.1Measurement Procedure........................................................................................................19 7.6.2Measurement Results .............................................................................................................19 8CONCLUSION ..................................................…

Text truncated - open the document above for the full version.

5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598 Certification Exhibit FCC ID: YWZ-HBCLB IC: 3356F-HBCLB FCC Rule Part: 15.247 IC Radio Standards Specification: RSS-210 ACS Project Number: 13-0211 Manufacturer: Alpha - High Theft Solutions Model: HBCLOK Test Setup Photos Model: HBCLOKFCC ID: YWZ-HBCLBIC: 3356F-HBCLB ACS Project: 13-0211Advanced Compliance SolutionsPage 2 Figure 1: Radiated Emissions – XPOS Figure 2: Radiated Emissions – XPOS Model: HBCLOKFCC ID: YWZ-HBCLBIC: 3356F-HBCLB ACS Project: 13-0211Advanced Compliance SolutionsPage 3 Figure 3: Radiated Emissions – YPOS Figure 4: Radiated Emissions – YPOS Model: HBCLOKFCC ID: YWZ-HBCLBIC: 3356F-HBCLB ACS Project: 13-0211Advanced Compliance SolutionsPage 4 Figure 5: Radiated Emissions – ZPOS Figure 6: Radiated Emissions – ZPOS