Z3AP604BTDynamic Bluetooth 4.0 Headphones

Example: Android 4.0 Press Menu > Settings > Switch on Bluetooth > Bluetooth > Search for devices > P604 Wireless > Pair Notes: - Pairing mode will last up to ten minutes or until a device is found, two tones will sound to let you know when pairing has stopped. - If you exceed the effective range of approx. 10M (33ft) the headphone will disconnect and will automatically reconnect if the speaker re-enters the effective range within ten minutes. Phone Operations If the mobile device that is paired (via Bluetooth) with the P604 Wireless headphone is a cellular phone you can: LED Indicators Status Charging Battery Full On and Paired Paring Mode Low Battery Indication Red LED on Blue LED on Blue LED flashes Red and Blue LED will flash alternately Red LED flashes Reconnection 1. Turn on Bluetooth on phone. 2. Switch on the P604 Wireless by pressing the multifunction button for 3 seconds. 3. If your device was the latest one to be paired with the P604 Wireless it will connect automatically otherwise please repeat pairing section. Answer Call Press the once. End Call Press the once. Refuse Call Press and holdfor 2 seconds. Switch CallPress and holdfor 2 seconds while in a call. OFF Switch On Bluetooth ON Select P604 Wireless P604 Wireless ON Click Search for Devices Click Settings ON Bluetooth is On ON Now Connected P604 Wireless Select Bluetooth Click Settings Bluetooth is On Select P604 Wireless P604 Wireless Switch On Bluetooth Now Connected P604 Wireless Example: iOS Press Settings > Bluetooth and switch Bluetooth on > P604 Wireless > Pair Switch on Press the multifunction button for 3 seconds until the blue LED lights up Switch off Press the multifunction button for 3 seconds until the red LED lights up Function Diagram Getting Connected The P604 Wireless allows you to pair with your mobile device in 2 different ways: Charging the headset It is recommended to fully charge before initial use for better battery life. USB Chargers are available at chargers.arctic.ac The P604 Wireless can be charged while switched on or off. 1. Insert the micro USB cable into the P604 Wireless and the USB side into a power source. 2. When the Blue light on constantly the P604 Wireless is fully charged. Music Stutters 4 5 6 Switch On / Off multifunction button LED indicator Micro-USB charging Microphone Previous track Next track Smart Charger 4800 1. Switch on the P604 Wireless by Press the Multifunction Button for 3 seconds. 2. The P604 Wireless automatically enters pairing mode shown by the red and blue LED flash alternately. 3. Turn on Bluetooth on your phone and pair it with the headphone. A. Bluetooth Pairing 1. Switch on the P604 Wireless by Press the Multifunction Button for 3 seconds. 2. Enable NFC on your mobile device. 3. Slide your phone very slowly from top to bottom across the shown area of the right side of the headphone until you hear a beep and a confirmation message comes up on your mobile device. 4. Play music! B. NFC One Touch Pairing (only for NFC enabled phones) NFC antenna How to wear the headset Switch the Headset On or Off ButtonsButtons

AnnexNo.:BL-SZ15B0130-AW 1 / 4 EXTERNALEUTPHOTOS THEFRONTOFEUT THEBACKOFEUT AnnexNo.:BL-SZ15B0130-AW 2 / 4 THELEFTOFEUT THERIGHTOFEUT AnnexNo.:BL-SZ15B0130-AW 3 / 4 THEUPOFEUT THEDOWNOFEUT AnnexNo.:BL-SZ15B0130-AW 4 / 4 THEPHOTOOFCHARGINGCABLE

Label: Label_location:

AnnexNo.:BL-SZ15B0130-AI 1 / 8 INTERNALEUTPHOTOS EUTUNCOVERVIEW1 EUTUNCOVERVIEW2 AnnexNo.:BL-SZ15B0130-AI 2 / 8 EUTUNCOVERVIEW3 EUTUNCOVERVIEW4 AnnexNo.:BL-SZ15B0130-AI 3 / 8 MAINBOARDBACKVIEW5 EUTUNCOVERVIEW6 AnnexNo.:BL-SZ15B0130-AI 4 / 8 EUTUNCOVERVIEW7 EUTUNCOVERVIEW8

AnnexNo.:BL-SZ15B0130-AI 5 / 8 EUTUNCOVERVIEW9 MAINBOARDFRONTVIEW1 AnnexNo.:BL-SZ15B0130-AI 6 / 8 MAINBOARDBACKVIEW1 MAINBOARDBACKVIEW1 PCBAntenna RFChip AnnexNo.:BL-SZ15B0130-AI 7 / 8 MAINBOARDFRONTVIEW2 MAINBOARDBACKVIEW2 AnnexNo.:BL-SZ15B0130-AI 8 / 8 MAINBOARDFRONTVIEW3 MAINBOARDBACKVIEW3

RFExposureEvaluationforFCCID:Z3AP604BT ReferusermanualthisdeviceisaDynamicBluetooth4.0Headphonesandthisdevicewas designedusedinportabledevicestheminimumdistancebetweenhuman’sbodyis5mm.Based onthe47CFR2.1093,thisdevicebelongstoportabledevice.Thedefinitionofthecategoryas following: PortableDerives: CFRTitle47§2.1093(b) (b)Forpurposesofthissection,aportabledeviceisdefinedasatransmittingdevicedesigned tobeusedsothattheradiatingstructure(s)ofthedeviceis/arewithin20centimetersofthe bodyoftheuser. FCCKDB447498D01GeneralRFExposureGuidancev05r02Limit UnlessspecificallyrequiredbythepublishedRFexposureKDBprocedures,standalone1-ghead orbodyand10-gextremitySARevaluationforgeneralpopulationexposureconditions,by measurementornumericalsimulation,isnotrequiredwhenthecorrespondingSARTest ExclusionThresholdcondition,listedbelow,issatisfied.Thesetestexclusionconditionsare basedonsource-basedtime-averagedmaximumconductedoutputpoweroftheRFchannel requiringevaluation,adjustedfortune-uptolerance,andtheminimumtestseparationdistance requiredfortheexposureconditions.Theminimumtestseparationdistanceisdeterminedbythe smallestdistancefromtheantennaandradiatingstructuresoroutersurfaceofthedevice, accordingtothehostformfactor,exposureconditionsandplatformrequirements,toanypartof thebodyorextremityofauserorbystander. The1-gand10-gSARtestexclusionthresholdsfor100MHzto6GHzattestseparationdistances ≤50mmaredeterminedby: []·[]≤3.0for1-gSARand≤ 7.5for10-gextremitySAR Where •f(GHz)istheRFchanneltransmitfrequencyinGHz •PoweranddistanceareroundedtothenearestmWandmmbeforecalculation •Theresultisroundedtoonedecimalplaceforcomparison Thetestexclusionsareapplicableonlywhentheminimumtestseparationdistanceis≤50mm and fortransmissionfrequenciesbetween100MHzand6GHz.Whentheminimumtestseparation distanceis<5mm,adistanceof5mmisappliedtodetermineSARtestexclusion. FCCexclusioncondition=[]·[]=1.67 ＜ 3.0 RFExposureEvaluationResult:Pass Note:Morepowerdata,PleaserefertotheRFreport.

Report No.: BL-SZ15B0130-602 2 Revision History Version Issue Date Revisions Rev. 01 Dec. 3, 2015 Initial Issue TABLE OF CONTENTS 1 ADMINISTRATIVE DATA (GENERAL INFORMATION) ........................................................................ 5 1.1 Identification of the Testing Laboratory ............................................................................................ 5 1.2 Identification of the Responsible Testing Location ........................................................................... 5 1.3 aboratory Condition ......................................................................................................................... 5 1.4 Announce ........................................................................................................................................ 5 2 PRODUCT INFORMATION ................................................................................................................... 7 2.1 Applicant ......................................................................................................................................... 7 2.2 Manufacturer ................................................................................................................................... 7 2.3 Factory Information ......................................................................................................................... 7 2.4 General Description for Equipment under Test (EUT) ..................................................................... 7 2.5 Ancillary Equipment ......................................................................................................................... 7 2.6 Technical Information ...................................................................................................................... 8 3 SUMMARY OF TEST RESULTS ........................................................................................................... 9 3.1 Test Standards ................................................................................................................................ 9 3.2 Verdict ............................................................................................................................................. 9 4 GENERAL TEST CONFIGURATIONS ................................................................................................ 10 4.1 Test Environments ........................................................................................................................ 10 4.2 Test Equipment List ....................................................................................................................... 10 4.3 Test Configurations ....................................................................................................................... 11 4.4 Description of Test Setup .............................................................................................................. 11 4.4.1 For Antenna Port Test ............................................................................................................ 11 4.4.2 For AC Power Supply Port Test .............................................................................................. 11 4.4.3 For Radiated Test (Below 30 MHz) ......................................................................................... 12 4.4.4 For Radiated Test (30 MHz-1 GHz) ........................................................................................ 12 4.4.5 For Radiated Test (Above 1 GHz) .......................................................................................... 13 4.5 Test Conditions ............................................................................................................................. 13 Report No.: BL-SZ15B0130-602 3 5 TEST ITEMS ....................................................................................................................................... 14 5.1 Antenna Requirements .................................................................................................................. 14 5.1.1 Standard Applicable ............................................................................................................... 14 5.1.2 Antenna Anti-Replacement Construction ................................................................................ 14 5.1.3 Antenna Gain ......................................................................................................................... 14 5.2 Output Power ................................................................................................................................ 15 5.2.1 Test Limit ................................................................................................................................ 15 5.2.2 Test Setup .............................................................................................................................. 15 5.2.3 Test Procedure ....................................................................................................................... 15 5.2.4 Test Result ............................................................................................................................. 15 5.3 6 dB Bandwidth ............................................................................................................................. 16 5.3.1 Limit........................................................................................................................................ 16 5.3.2 Test Setup .............................................................................................................................. 16 5.3.3 Test Procedure ....................................................................................................................... 16 5.3.4 Test Result ..........................................................................................................…

Text truncated - open the document above for the full version.

Annex No.: BL-SZ15B0130-AR TEST SETUP PHOTOS 1 Radiated Test Photo Below 30MHz 30 MHz-1 GHz Annex No.: BL-SZ15B0130-AR Above 1GHz 1 Above 1GHz 2 Annex No.: BL-SZ15B0130-AR 2 Conducted Test Photo Conducted Test 3 Conducted Emission Conducted Emission Test